< img height="1" width="1" style="display:none" src="https://www.facebook.com/tr?id=26825290190466607&ev=PageView&noscript=1" />

Nullam dignissim, ante scelerisque the is euismod fermentum odio sem semper the is erat, a feugiat leo urna eget eros. Duis Aenean a imperdiet risus.

Nail-Head Defects in HDI Drilling: A Practical Fault-Isolation Guide

  • Nail-Head Defects in HDI Drilling: A Practical Fault-Isolation Guide author
  • 11th November 2026

The first clue may be a rejected cross-section, not a rough-looking hole. Copper at an inner layer has bent or spread, although the board surface looks ordinary. In HDI and multilayer production, that is a different investigation from chasing a visible burr. Keep the suspect panel, record its place in the drill stack, and examine a section before changing the setup. Otherwise an apparent improvement after a tool change may simply reflect a different panel or a different point in the drill’s life.

Nail-Head Defects in HDI Drilling A Practical Fault-Isolation Guide

In FR-4, the edge passes through glass fiber, resin, and copper. Glass is abrasive, resin retains heat, and copper can deform rather than break cleanly. TSHZ identifies worn edges and copper pulled during drill withdrawal as nail-head mechanisms in PCB work. A worn drill may also leave rough walls or drift from its intended hole position. The inspection sheet should have separate entries for those faults. “Bad holes” gives the next shift almost nothing to work with.

Confirm the defect before changing the drill

Where to inspect a cross-section

Nail heading is deformation of copper at the inner-layer interface visible in a prepared hole cross-section. Save an image of the whole hole as well as a close view of the affected layer. Label the layer, panel, and drilling sequence on the image. A nearby acceptable hole from the same setup is a useful reference. Without it, “rough” or “pulled” can mean different things to the drilling and quality teams.

A number written into a supplier FAQ is not the acceptance limit for every PCB. Use the drawing and the plant’s inspection method. If the copper shape is borderline, identify the measurement points and retain the prepared section. Preparation damage can confuse the reading; section another hole if necessary. Changing feed before the feature is agreed upon wastes a trial.

Separate nail heading, burrs, and resin smear

An entry or exit burr sits at the board surface. Nail heading sits at buried copper. Resin smear is different again: softened resin can coat the wall and interfere with exposed copper. The University of Maryland CALCE explanation of resin smear helps identify that wall condition. Several faults may be present on one panel. Give each one its own photograph and description.

Write a separate note for the surface burr and the buried copper. Add wall condition and hole position. Which panel was cut? A technician repeating the inspection tomorrow should be able to find the same feature without guessing. If a trial makes the entrance clean but leaves the inner layer distorted, the work is not finished.

Record the pattern across the panel and stack

Top versus lower panels

“Sample from the stack” is a poor label. Number the panels from top to bottom and put that number on each cross-section. An upper-panel failure that appears immediately may call for a fresh-tool or entry check; gradual deterioration down the stack points elsewhere. TSHZ’s PCB guidance warns that adding layers to a stack increases drill deflection risk and can reduce positional accuracy, especially with small diameters. A short drill is stiffer and less prone to wandering than an unnecessarily long one. Check both dimensions against the actual setup before deciding that nail heading is caused by wear alone.

The drilling traveler should identify entry and backing materials and how the panels were held. Measure actual drilling depth. Is the flute long enough to clear the full stack? Is the exposed drill longer than necessary? If coordinate data exist, compare hole position on upper and lower panels. A trend down the stack merits a setup check, even when edge wear is also visible.

Early holes versus late holes

Pick holes from the start and late part of the same drill run. Section them in the same way. A late sample with worse copper deformation is useful only if its laminate, hole size, and stack are known. Ask whether the wall has also become rougher or the hole position has moved. TSHZ recommends looking at hole-wall quality and visible edge wear when deciding when to replace a PCB micro drill. Keep the used edge with its sample record, rather than a tray of unlabelled drills.

The first holes are defective. That points to the setup before a wear-life discussion: was the specified drill fitted, did it seat correctly, what was the runout, and which entry and backing materials were used? Record feed, speed, and stack height. A defect that appears only much later has a different timeline; pull that drill and inspect its edge and flutes. Treating the two timelines as one problem makes both harder to solve.

Test the likely causes in order

Edge condition and replacement timing

Glass fiber in FR-4 abrades the edge; copper can be drawn into a deformed shape as the edge loses cutting ability or during withdrawal. In HDI drilling, carbide drill wear can coincide with nail heading, rough hole walls, and positional drift. That combination is a reason to examine the point and cutting edges, then match the edge photograph to the holes drilled with that tool. It is not a guarantee that another factory will see the symptoms in the same order.

Keep the first acceptable section and the last one before the defect limit is crossed. Put the corresponding edge images beside them. This gives purchasing and production a replacement point tied to their board, rather than a hole-count figure borrowed from another laminate. TSHZ also advises against routine regrinding of a diamond-coated micro drill because grinding can remove the coating and alter the edge geometry. If regrinding is attempted, its output belongs in a separate trial record.

Chip evacuation and heat

The hole contains a difficult mix: abrasive glass fiber, insulating resin, and ductile copper. Resin’s poor heat conduction can leave local heat around a drill, while packed chips change contact at the edge. Pull the suspect drill and inspect the flutes for loading. Section a nearby hole to check for smear. Heat and chip removal may matter even if nail heading is the rejected feature. The Arlon drilling-defects technical note gives a useful reference for reading drill wear alongside cutting conditions.

There is a temptation to change everything when scrap is rising. Resist it for the short diagnostic run. Change feed, or stack, or tool type, then compare the same panel position. Four simultaneous changes may produce a good section without showing which one helped. The withdrawal setting belongs on the sheet as well; the copper can be pulled on the way out.

Stack support, length, and machine condition

Measure runout at the fitted tool, not merely at an empty spindle. Check seating, spindle condition, and whether the stack lies flat. A short total length improves rigidity for PCB drilling; too many stacked panels increase deflection risk for small drills. That is a direction for testing, not a universal stack count. If one machine produces the damage and another does not, investigate the machine before assuming that the drill design is wrong.

On lower panels, look at the backing and the withdrawal move. On one suspect spindle, check the spindle. It sounds basic, yet a tool trial often arrives with no record of which copper layer was rejected. Attach two labelled sections to each change request: one before and one after. They will settle more than a note saying “new drill helped.”

When a different drill is the useful experiment

TS-A01UC for HDI micro-hole trials

TSHZ offers a PCB diamond drill bit range for general multilayer and HDI boards. Its TS-A01UC micro drill is specified for HDI and multilayer work; the UC flute is intended to improve chip evacuation in dense small-hole drilling. It is worth trialling when worn edges or chip-packed flutes are part of the defect record. A fresh coated drill cannot compensate for a loose stack or a spindle running out.

Specify diameter and effective length against the finished-hole requirement, plating allowance, and actual stack. TSHZ also offers TS-A02 ST for standard FR-4/CEM work and TS-A03 for larger-diameter or thicker-board drilling. When comparing series, record the geometry and length as well as the coating; more than one property may have changed. The separate HDI and multilayer drill comparison covers that selection decision in more detail.

PCB diamond drill bit

Compare on the same board and inspection method

Run the candidate against the same laminate, stack, diameter, machine, and sectioning method as the current drill. Sample near the beginning and end of each tool run. Record the buried copper, surface burr, wall, hole position, and edge. An improved entrance with unchanged inner-layer distortion is an entrance improvement, not a nail-head solution. Extend the comparison far enough into the run to see whether the result holds.

What to send with a tooling inquiry

An inquiry is easier to answer when it includes the laminate and board build, copper-layer arrangement, finished-hole target, current drill diameter and length, total stack, machine, and spindle. Attach edge and cross-section images labelled with panel position and hole count. Include feed, speed, withdrawal settings, and the board’s own acceptance requirement. TSHZ’s PCB application page covers the board-material context. The labelled samples show the precise failure under discussion.

FAQ

Is every copper burr a nail head?

No. Surface burrs appear at entry or exit. Nail heading is evaluated at an inner copper layer in a prepared hole cross-section. Report both if both are present.

Does a diamond-coated drill remove the need to check the stack?

No. The drill edge, flute, length, stack support, runout, and withdrawal condition all affect the result. A coated tool trial is most informative after the defect pattern has been documented.

What should trigger a drill replacement review?

A change in hole-wall quality, nail-heading trend, roughness, positional accuracy, or visible cutting-edge wear is a reason to review the replacement interval. Use the plant’s own inspection requirement and board construction rather than a copied universal hole count.

Tags:

Table of Contents

Frequently Asked Questions

"Price is what you pay, Cost is what you lose. A $15 tool that stops your $200k machine every 2 hours is the most expensive thing in your shop. Our CVD tool costs more because it buys you 40 hours of uninterrupted 'spindle-on' time. Which one saves you more by the end of the month?
I love skeptics—they usually become our best customers. In G5 Graphite or 18% Silicon Aluminum, standard carbide yields to abrasion in minutes. Our $8000 HV$ diamond crystalline layer literally ignores that abrasion. We don’t just claim it; we have the micro-wear test reports to back it up. Want to see the comparison video?
Stop right there. I’d love to sell you a tool, but Diamond and Iron are 'enemies' at high temperatures (chemical affinity). For steel, use our AlTiN series. But if you’re cutting Graphite, CFRP, or Ceramics, our CVD is the undisputed king. We sell solutions, not just metal.
That’s the difference between DLC (Diamond-Like Carbon) and True CVD. Most cheap 'diamond' tools are just thin films. Our CVD is chemically grown into the carbide substrate. It doesn't just sit on top; it's part of the tool. No peeling, just pure cutting.
Actually, it improves it. Because the diamond layer is ultra-smooth and the edge stays sharp 20x longer, you avoid the 'tearing' effect of a dull tool. You get a mirror-like finish on the 100th part just as you did on the 1st.
Don't sell them a tool; sell them 'Machine Capacity.' Tell your customers: 'Would you rather buy 1 tool and run all night, or buy 20 tools and pay someone to stand there and change them?' The labor savings alone pay for the tool.
"Diamond loves speed. High RPM is where it shines. We provide a customized cutting data sheet with every order. If you’re not sure, send us your material grade and we’ll calculate the optimal Vc and Fz for you. We don't just ship tools; we ship success."
We control coating thickness within $\pm 2\mu m$. In high-precision graphite electrode machining, we know microns matter. Our QC report for every batch ensures your offsets stay consistent from tool #1 to tool #100.
We stock standard sizes for immediate dispatch. We use DHL/FedEx—typically 4-7 days to your doorstep. We know a downed machine is a bleeding wound, and we’re here to stop the bleeding fast.
We offer 'Performance Guarantee' samples for qualified shops. We don't give them away for free because high-end tech has a cost, but if it doesn't outperform your current tool by at least 10X, the next one is on me. Fair enough?
A pure diamond film is "grown" onto the surface of a carbide substrate using chemical vapor deposition (CVD) technology. This film exhibits properties close to those of natural diamond, giving the tool exceptional hardness and wear resistance.
The hardness of a CVD diamond coating reaches up to 9000HV, making it one of the hardest tool coatings available in industry today.
When machining graphite materials, tool life typically increases by 3 to 18 times; in PCB processing, life extension can reach 20 to 30 times.
Graphite is highly abrasive and brittle, causing rapid wear on conventional tools. The high hardness of diamond coatings effectively resists wear and prevents chipping at the cutting edge.
4-flute: suitable for finishing or hard graphite, providing better surface finish. 2-flute: ideal for deep slotting or small-diameter tools (below D2), ensuring sufficient chip evacuation space and preventing tool breakage.
n principle, drill diameter = finished hole diameter – plating copper thickness compensation. A common recommendation is to add 0.03–0.05 mm compensation for finished hole diameters over 0.5 mm.
Whether machining graphite or PCBs, shorter overall lengths provide improved rigidity, reducing runout and minimizing the risk of tool breakage during operation.
This refers to deformation formed on the inner wall of a drilled hole due to drill wear or pulling action on the copper foil during retraction. Using CVD diamond-coated tools significantly reduces nail heads, improving hole wall quality.
Regrounding is not recommended. Reshaping would damage the diamond coating, exposing the lower-hardness substrate and drastically reducing performance.
Typically, replace the tool when hole wall quality deteriorates (e.g., burrs or nail heads exceeding 50 μm), visible edge wear under microscope, or when the processed quantity reaches 80–90% of the recommended tool life.
Although their unit price is typically 3–5 times higher than standard tungsten carbide tools, their extended lifespan results in a lower cost per hole, making them more economical in the long run.
High abrasiveness: The glass fibers in PCB materials are extremely hard and brittle, causing rapid wear of standard drill bits. Burrs and nail heads: Copper foil has high ductility, making it prone to burr formation at hole entrances or "nail head" defects when exiting, resulting in poor hole wall quality. Heat dissipation issues: Resin has low thermal conductivity; localized overheating can soften the tool.
Ultra-high wear resistance: Coating hardness reaches 9000HV, with a service life 20–30 times longer than conventional carbide drills. Reduced defects: Exceptionally sharp cutting edges significantly minimize burr and nail head formation. Thermal stability: Diamond has excellent thermal conductivity, enabling efficient heat dissipation and preventing resin burn on hole walls.
HDI/multilayer boards: Recommend TS-A01UC series, featuring a special UC flute design for superior chip evacuation, ideal for high-density micro-holes. Standard FR-4/CEM boards: Recommend TS-A02 ST standard series, offering the best cost-performance ratio. Large-diameter/thick boards: Recommend TS-A03 series, capable of drilling up to 6.50mm diameter with shank larger than drill diameter.
Exit burrs: Add a 0.3–0.5mm aluminum backing plate underneath the board and optimize retraction parameters. Entry burrs: Reduce feed rate during entry or switch to sharper diamond-coated drill bits.
Latest Product

Check out our Product

View More
PCB drilling bit

PCB diamond drill bit

PCB drill bits with excellent chip removal and hole roughness capabilities, long service life, suitable for drilling general multilayer and HDI boards, FR-4, CEM-1 boards, and eco-friendly boards. Diameter range: 0.1–3.175 mm,For the latest PCB boards, diamond-coated drills achieve over 3,000 holes per bit.
Read More
Diamond-coated PCB tool

PCB Diamond-Coated Milling Cutters

PCB diamond-coated milling cutters, also known as PCB routing cutters, printed circuit board milling cutters, or engraving cutters, are primarily used for contour cutting, slotting, depth-controlled milling, V-grooving, half-hole machining, and gold finger chamfering of PCBs; they are the most commonly used carbide tools in post-PCB manufacturing processes.
Read More
Dental-burs-1

CVD Diamond Dental burs

Micron-level precision cutting, balancing ultimate wear resistance with a gentle clinical experience,This series of dental burs features a high-purity integrated stainless steel/carbide substrate, coated with advanced CVD nano-diamond (or high-density natural diamond grit electroplating). Engineered for high-intensity clinical procedures such as tooth preparation, cavity access, decay removal, cosmetic restoration (veneer prep), and crown/bridge cutting. The ultra-hard, uniformly distributed diamond coating delivers aggressive cutting efficiency while minimizing frictional heat to protect the dental pulp, making it the premium choice for modern digital dentistry.
Read More
Flat-bottom-cylindrical-end-mill-1

Diamond coating Flat-bottom cylindrical end mill

Standard 2-flute/4-flute design with sharp cutting edges and large chip clearance space, suitable for efficient roughing and semi-finishing of graphite electrodes.
Read More
Get Standed
Is your tooling keeping up with the "Difficult-to-Machine" era?

Leave A Message

Graphite, Ceramics, and Carbon Fiber are the future, but they are “tool killers.” If you’re still using traditional coating, you’re fighting a losing battle.
Our CVD (Chemical Vapor Deposition) Diamond Coating creates a real crystalline diamond layer on the carbide substrate. This isn’t just a “finish”—it’s a shield.

Why top distributors choose our CVD series:
1.Ultra-Low Friction: Prevents chip welding and heat buildup.
2.Extreme Abrasion Resistance: Maintains sharp cutting edges $20 \times$ longer.
3.Surface Finish: Mirror-like results on the workpiece, zero secondary polishing needed.

    Your Name*

    Email

    Tel

    WhatsApp*

    Message

    Products
    Contacts
    WhatsApp
    Email