위엄 없음, scelerisque 이전에는 euismod fermentum 증오입니다 sem semper the is erat, a feugiat leo urna eget eros. 뒤이스 에네안 웃음을 위한 헤어컷.

Nail-Head Defects in HDI Drilling: A Practical Fault-Isolation Guide

  • Nail-Head Defects in HDI Drilling: A Practical Fault-Isolation Guide 작가
  • 11th 11월 2026

The first clue may be a rejected cross-section, not a rough-looking hole. Copper at an inner layer has bent or spread, although the board surface looks ordinary. In HDI and multilayer production, that is a different investigation from chasing a visible burr. Keep the suspect panel, record its place in the drill stack, and examine a section before changing the setup. Otherwise an apparent improvement after a tool change may simply reflect a different panel or a different point in the drill’s life.

Nail-Head Defects in HDI Drilling A Practical Fault-Isolation Guide

In FR-4, the edge passes through glass fiber, resin, and copper. Glass is abrasive, resin retains heat, and copper can deform rather than break cleanly. TSHZ identifies worn edges and copper pulled during drill withdrawal as nail-head mechanisms in PCB work. A worn drill may also leave rough walls or drift from its intended hole position. The inspection sheet should have separate entries for those faults. “Bad holes” gives the next shift almost nothing to work with.

Confirm the defect before changing the drill

Where to inspect a cross-section

Nail heading is deformation of copper at the inner-layer interface visible in a prepared hole cross-section. Save an image of the whole hole as well as a close view of the affected layer. Label the layer, panel, and drilling sequence on the image. A nearby acceptable hole from the same setup is a useful reference. Without it, “rough” or “pulled” can mean different things to the drilling and quality teams.

A number written into a supplier FAQ is not the acceptance limit for every PCB. Use the drawing and the plant’s inspection method. If the copper shape is borderline, identify the measurement points and retain the prepared section. Preparation damage can confuse the reading; section another hole if necessary. Changing feed before the feature is agreed upon wastes a trial.

Separate nail heading, burrs, and resin smear

An entry or exit burr sits at the board surface. Nail heading sits at buried copper. Resin smear is different again: softened resin can coat the wall and interfere with exposed copper. The University of Maryland CALCE explanation of resin smear helps identify that wall condition. Several faults may be present on one panel. Give each one its own photograph and description.

Write a separate note for the surface burr and the buried copper. Add wall condition and hole position. Which panel was cut? A technician repeating the inspection tomorrow should be able to find the same feature without guessing. If a trial makes the entrance clean but leaves the inner layer distorted, the work is not finished.

Record the pattern across the panel and stack

Top versus lower panels

“Sample from the stack” is a poor label. Number the panels from top to bottom and put that number on each cross-section. An upper-panel failure that appears immediately may call for a fresh-tool or entry check; gradual deterioration down the stack points elsewhere. TSHZ’s PCB guidance warns that adding layers to a stack increases drill deflection risk and can reduce positional accuracy, especially with small diameters. A short drill is stiffer and less prone to wandering than an unnecessarily long one. Check both dimensions against the actual setup before deciding that nail heading is caused by wear alone.

The drilling traveler should identify entry and backing materials and how the panels were held. Measure actual drilling depth. Is the flute long enough to clear the full stack? Is the exposed drill longer than necessary? If coordinate data exist, compare hole position on upper and lower panels. A trend down the stack merits a setup check, even when edge wear is also visible.

Early holes versus late holes

Pick holes from the start and late part of the same drill run. Section them in the same way. A late sample with worse copper deformation is useful only if its laminate, hole size, and stack are known. Ask whether the wall has also become rougher or the hole position has moved. TSHZ recommends looking at hole-wall quality and visible edge wear when deciding when to replace a PCB micro drill. Keep the used edge with its sample record, rather than a tray of unlabelled drills.

The first holes are defective. That points to the setup before a wear-life discussion: was the specified drill fitted, did it seat correctly, what was the runout, and which entry and backing materials were used? Record feed, speed, and stack height. A defect that appears only much later has a different timeline; pull that drill and inspect its edge and flutes. Treating the two timelines as one problem makes both harder to solve.

Test the likely causes in order

Edge condition and replacement timing

Glass fiber in FR-4 abrades the edge; copper can be drawn into a deformed shape as the edge loses cutting ability or during withdrawal. In HDI drilling, carbide drill wear can coincide with nail heading, rough hole walls, and positional drift. That combination is a reason to examine the point and cutting edges, then match the edge photograph to the holes drilled with that tool. It is not a guarantee that another factory will see the symptoms in the same order.

Keep the first acceptable section and the last one before the defect limit is crossed. Put the corresponding edge images beside them. This gives purchasing and production a replacement point tied to their board, rather than a hole-count figure borrowed from another laminate. TSHZ also advises against routine regrinding of a diamond-coated micro drill because grinding can remove the coating and alter the edge geometry. If regrinding is attempted, its output belongs in a separate trial record.

Chip evacuation and heat

The hole contains a difficult mix: abrasive glass fiber, insulating resin, and ductile copper. Resin’s poor heat conduction can leave local heat around a drill, while packed chips change contact at the edge. Pull the suspect drill and inspect the flutes for loading. Section a nearby hole to check for smear. Heat and chip removal may matter even if nail heading is the rejected feature. The Arlon drilling-defects technical note gives a useful reference for reading drill wear alongside cutting conditions.

There is a temptation to change everything when scrap is rising. Resist it for the short diagnostic run. Change feed, or stack, or tool type, then compare the same panel position. Four simultaneous changes may produce a good section without showing which one helped. The withdrawal setting belongs on the sheet as well; the copper can be pulled on the way out.

Stack support, length, and machine condition

Measure runout at the fitted tool, not merely at an empty spindle. Check seating, spindle condition, and whether the stack lies flat. A short total length improves rigidity for PCB drilling; too many stacked panels increase deflection risk for small drills. That is a direction for testing, not a universal stack count. If one machine produces the damage and another does not, investigate the machine before assuming that the drill design is wrong.

On lower panels, look at the backing and the withdrawal move. On one suspect spindle, check the spindle. It sounds basic, yet a tool trial often arrives with no record of which copper layer was rejected. Attach two labelled sections to each change request: one before and one after. They will settle more than a note saying “new drill helped.”

When a different drill is the useful experiment

TS-A01UC for HDI micro-hole trials

TSHZ offers a PCB 다이아몬드 드릴 비트 range for general multilayer and HDI boards. Its TS-A01UC micro drill is specified for HDI and multilayer work; the UC flute is intended to improve chip evacuation in dense small-hole drilling. It is worth trialling when worn edges or chip-packed flutes are part of the defect record. A fresh coated drill cannot compensate for a loose stack or a spindle running out.

Specify diameter and effective length against the finished-hole requirement, plating allowance, and actual stack. TSHZ also offers TS-A02 ST for standard FR-4/CEM work and TS-A03 for larger-diameter or thicker-board drilling. When comparing series, record the geometry and length as well as the coating; more than one property may have changed. The separate HDI and multilayer drill comparison covers that selection decision in more detail.

PCB diamond drill bit

Compare on the same board and inspection method

Run the candidate against the same laminate, stack, diameter, machine, and sectioning method as the current drill. Sample near the beginning and end of each tool run. Record the buried copper, surface burr, wall, hole position, and edge. An improved entrance with unchanged inner-layer distortion is an entrance improvement, not a nail-head solution. Extend the comparison far enough into the run to see whether the result holds.

What to send with a tooling inquiry

An inquiry is easier to answer when it includes the laminate and board build, copper-layer arrangement, finished-hole target, current drill diameter and length, total stack, machine, and spindle. Attach edge and cross-section images labelled with panel position and hole count. Include feed, speed, withdrawal settings, and the board’s own acceptance requirement. TSHZ’s PCB 적용 페이지 covers the board-material context. The labelled samples show the precise failure under discussion.

자주 묻는 질문

Is every copper burr a nail head?

No. Surface burrs appear at entry or exit. Nail heading is evaluated at an inner copper layer in a prepared hole cross-section. Report both if both are present.

Does a diamond-coated drill remove the need to check the stack?

No. The drill edge, flute, length, stack support, runout, and withdrawal condition all affect the result. A coated tool trial is most informative after the defect pattern has been documented.

What should trigger a drill replacement review?

A change in hole-wall quality, nail-heading trend, roughness, positional accuracy, or visible cutting-edge wear is a reason to review the replacement interval. Use the plant’s own inspection requirement and board construction rather than a copied universal hole count.

태그:

목차

자주 묻는 질문

"가격은 지불하는 것이고, 비용은 잃는 것입니다. 20만 달러짜리 기계를 2시간마다 멈추게 하는 15달러짜리 공구는 공장에서 가장 비싼 물건입니다. 저희 CVD 공구는 가격이 더 높지만, 40시간 동안 중단 없이 스핀들을 가동할 수 있도록 해줍니다. 결국 어느 쪽이 더 많은 비용을 절감해 줄까요?"
저는 회의적인 사람들을 좋아합니다. 그들이 바로 저희 최고의 고객이 되는 경우가 많거든요. G5 흑연이나 18% 실리콘 알루미늄 소재의 일반 초경합금은 몇 분 만에 마모됩니다. 하지만 저희의 8,000달러짜리 HV$ 다이아몬드 결정층은 그런 마모를 전혀 견뎌내지 못합니다. 저희는 단순히 주장만 하는 것이 아니라, 이를 뒷받침하는 미세 마모 시험 보고서를 보유하고 있습니다. 비교 영상을 보고 싶으신가요?
잠깐만요. 공구를 팔고 싶지만, 다이아몬드와 철은 고온에서 화학적 친화력 때문에 '적'과 같습니다. 강철에는 저희 AlTiN 시리즈를 사용하세요. 하지만 흑연, 탄소섬유강화플라스틱(CFRP), 세라믹을 절삭할 때는 저희 CVD 방식이 단연 최고입니다. 저희는 금속만 파는 게 아니라 솔루션을 제공합니다.
이것이 바로 DLC(다이아몬드 유사 탄소)와 진정한 CVD의 차이점입니다. 대부분의 저가형 '다이아몬드' 공구는 얇은 막으로만 이루어져 있습니다. 저희 CVD는 탄화물 기판에 화학적으로 성장시킨 것입니다. 단순히 표면에 얹는 것이 아니라 공구의 일부가 됩니다. 벗겨짐 없이 순수한 절삭 성능을 제공합니다.
실제로 품질을 향상시켜 줍니다. 다이아몬드 코팅층이 매우 매끄럽고 날카로움이 20배 더 오래 유지되기 때문에 무딘 공구로 인한 '찢어짐' 현상을 방지할 수 있습니다. 첫 번째 부품과 마찬가지로 100번째 부품에서도 거울처럼 매끄러운 마감을 얻을 수 있습니다.
고객에게 공구를 팔지 말고 '기계 가동률'을 파세요. 이렇게 말하세요. '공구 하나를 사서 밤새도록 가동하시겠습니까, 아니면 공구 20개를 사서 누군가에게 공구를 교체하도록 돈을 지불하시겠습니까?' 인건비 절감만으로도 공구 가격을 충분히 상쇄할 수 있습니다.
"다이아몬드는 속도를 좋아합니다. 고속 회전일 때 가장 빛을 발하죠. 모든 주문에 맞춤형 절삭 데이터 시트를 제공해 드립니다. 잘 모르시겠다면 재질 등급을 알려주시면 최적의 Vc와 Fz 값을 계산해 드리겠습니다. 저희는 단순히 공구만 배송하는 것이 아니라 성공을 함께 배송합니다."
당사는 코팅 두께를 ±2μm 이내로 정밀하게 제어합니다. 고정밀 흑연 전극 가공에서는 미세한 차이도 중요하다는 것을 잘 알고 있습니다. 모든 배치에 대한 품질 관리 보고서를 통해 모든 공구에서 오프셋이 일관되게 유지되도록 보장합니다.
저희는 표준 사이즈 제품을 재고로 보유하고 있어 즉시 배송 가능합니다. DHL/FedEx를 이용하며, 일반적으로 4~7일 이내에 도착합니다. 기계 고장은 심각한 피해라는 것을 잘 알고 있으며, 저희는 그 피해를 신속하게 복구해 드리겠습니다.
저희는 자격을 갖춘 업체에 한해 '성능 보증' 샘플을 제공합니다. 고가의 기술에는 비용이 따르기 때문에 무료로 제공하지는 않지만, 만약 저희 제품이 현재 사용하시는 장비보다 최소 10배 이상 뛰어난 성능을 보여주지 못한다면, 다음 제품은 저희가 무료로 제공해 드립니다. 괜찮으시죠?
화학 기상 증착(CVD) 기술을 이용하여 탄화물 기판 표면에 순수 다이아몬드 박막을 "성장"시킵니다. 이 박막은 천연 다이아몬드와 유사한 특성을 나타내어 공구에 탁월한 경도와 내마모성을 제공합니다.
CVD 다이아몬드 코팅의 경도는 최대 9000HV에 달하여 오늘날 산업계에서 사용 가능한 가장 단단한 공구 코팅 중 하나입니다.
흑연 소재를 가공할 때 공구 수명은 일반적으로 3~18배 증가하며, PCB 가공에서는 20~30배까지 연장될 수 있습니다.
흑연은 마모성이 매우 높고 부서지기 쉬워 기존 공구의 마모를 빠르게 유발합니다. 반면 다이아몬드 코팅은 높은 경도로 마모를 효과적으로 방지하고 절삭날의 파손을 막아줍니다.
4날: 마무리 작업이나 경질 흑연 작업에 적합하며, 더 나은 표면 마감을 제공합니다. 2날: 깊은 슬로팅이나 소구경 공구(D2 미만)에 이상적이며, 충분한 칩 배출 공간을 확보하고 공구 파손을 방지합니다.
원칙적으로 드릴 직경은 최종 구멍 직경에서 도금 구리 두께를 뺀 값과 같습니다. 일반적으로 최종 구멍 직경이 0.5mm를 초과하는 경우 0.03~0.05mm를 보정하는 것이 좋습니다.
흑연이나 PCB를 가공할 때, 전체 길이가 짧을수록 강성이 향상되어 런아웃이 줄어들고 작업 중 공구 파손 위험이 최소화됩니다.
이는 드릴 마모 또는 드릴 후퇴 시 구리 호일에 가해지는 당김 작용으로 인해 드릴 구멍의 내벽에 발생하는 변형을 말합니다. CVD 다이아몬드 코팅 공구를 사용하면 못 머리가 크게 줄어들어 구멍 벽 품질이 향상됩니다.
재연마는 권장하지 않습니다. 재성형 과정에서 다이아몬드 코팅이 손상되어 경도가 낮은 기판이 노출되고 성능이 급격히 저하될 수 있습니다.
일반적으로 공구는 홀 벽 품질이 저하될 때(예: 50μm를 초과하는 버 또는 못 머리), 현미경으로 확인했을 때 모서리 마모가 보일 때, 또는 가공량이 권장 공구 수명의 80~90%에 도달했을 때 교체해야 합니다.
일반적으로 텅스텐 카바이드 공구보다 단가가 3~5배 높지만, 수명이 길어 구멍당 비용이 절감되어 장기적으로는 더 경제적입니다.
높은 마모성: PCB 재료에 포함된 유리 섬유는 매우 단단하고 부서지기 쉬워 일반 드릴 비트의 마모를 빠르게 유발합니다. 버 및 못머리: 구리 호일은 연성이 높아 구멍 입구에 버가 생기거나 구멍 밖으로 나올 때 "못머리" 모양의 결함이 발생하기 쉬워 구멍 벽면 품질이 저하됩니다. 열 방출 문제: 레진은 열전도율이 낮아 국부적인 과열이 발생하면 공구가 연화될 수 있습니다.
초고내마모성: 코팅 경도는 9000HV에 달하며, 수명은 기존 초경 드릴보다 20~30배 더 깁니다. 결함 감소: 매우 날카로운 절삭날이 버(burr) 및 못머리(nail head) 형성을 크게 최소화합니다. 열 안정성: 다이아몬드는 열전도율이 뛰어나 효율적인 열 방출을 가능하게 하고 구멍 벽면의 수지 연소를 방지합니다.
HDI/다층 기판: 칩 배출 성능이 뛰어난 특수 UC 플루트 디자인이 적용된 TS-A01UC 시리즈를 권장합니다. 고밀도 마이크로홀에 이상적입니다. 표준 FR-4/CEM 보드: 최고의 가격 대비 성능을 제공하는 TS-A02 ST 표준 시리즈를 권장합니다. 직경이 크거나 두꺼운 판재의 경우, 드릴 직경보다 큰 생크를 사용하여 최대 6.50mm 직경까지 드릴링이 가능한 TS-A03 시리즈를 권장합니다.
출구 버(burr) 제거: 기판 아래에 0.3~0.5mm 두께의 알루미늄 백킹 플레이트를 추가하고 리트랙션 매개변수를 최적화하십시오. 진입 시 발생하는 버(burr): 진입 시 이송 속도를 줄이거나 더 날카로운 다이아몬드 코팅 드릴 비트로 교체하십시오.
최신 제품

저희 제품을 확인해 보세요

더 보기
PCB drilling bit

PCB 다이아몬드 드릴 비트

칩 제거 및 홀 표면 조도가 우수하고 수명이 긴 PCB 드릴 비트로, 일반 다층 기판 및 HDI 기판, FR-4, CEM-1 기판, 친환경 기판 드릴링에 적합합니다. 직경 범위: 0.1~3.175mm, 최신 PCB 기판용으로 다이아몬드 코팅 드릴은 비트당 3,000개 이상의 구멍을 뚫을 수 있습니다.
더 읽어보기
Diamond-coated PCB tool

PCB 다이아몬드 코팅 밀링 커터

PCB 다이아몬드 코팅 밀링 커터는 PCB 라우팅 커터, 인쇄 회로 기판 밀링 커터 또는 조각 커터라고도 하며, 주로 PCB의 윤곽 절단, 슬로팅, 깊이 제어 밀링, V 홈 가공, 반구멍 가공 및 골드 핑거 모따기에 사용됩니다. 이러한 커터는 PCB 후처리 공정에서 가장 일반적으로 사용되는 초경 공구입니다.
더 읽어보기
Dental-burs-1

CVD 다이아몬드 치과용 버

마이크론 수준의 정밀 절삭과 뛰어난 내마모성, 그리고 부드러운 임상 경험의 균형을 자랑하는 이 치과용 버 시리즈는 고순도 일체형 스테인리스 스틸/카바이드 기판에 첨단 CVD 나노 다이아몬드(또는 고밀도 천연 다이아몬드 입자 전기 도금) 코팅을 적용했습니다. 치아 준비, 와동 접근, 충치 제거, 심미 수복(베니어 준비), 크라운/브릿지 절삭과 같은 고강도 임상 시술에 적합하도록 설계되었습니다. 초경질의 균일하게 분포된 다이아몬드 코팅은 강력한 절삭 효율을 제공하는 동시에 마찰열을 최소화하여 치수를 보호하므로 현대 디지털 치과에 최적의 선택입니다.
더 읽어보기
Flat-bottom-cylindrical-end-mill-1

다이아몬드 코팅 평저 원통형 엔드밀

날카로운 절삭날과 넓은 칩 배출 공간을 갖춘 표준 2날/4날 설계로, 흑연 전극의 효율적인 황삭 및 준정삭에 적합합니다.
더 읽어보기
Get Standed
귀사의 공구는 "가공하기 어려운 소재" 시대에 발맞춰 발전하고 있습니까?

메시지를 남겨주세요

흑연, 세라믹, 탄소 섬유는 미래의 소재이지만, 공구를 망가뜨리는 주범이기도 합니다. 만약 아직도 전통적인 코팅 방식을 고수하고 있다면, 승산 없는 싸움을 하고 있는 것입니다.
당사의 CVD(화학 기상 증착) 다이아몬드 코팅은 탄화물 기판 위에 실제 결정질 다이아몬드 층을 형성합니다. 이는 단순한 "마감재"가 아니라 보호막입니다.

주요 유통업체들이 당사의 CVD 시리즈를 선택하는 이유:
1. 초저마찰: 칩 용접 및 열 축적을 방지합니다.
2. 뛰어난 내마모성: 날카로운 절삭면을 20배 더 오래 유지합니다.
3. 표면 마감: 가공물에 거울처럼 매끄러운 결과가 나타나며, 2차 연마가 전혀 필요하지 않습니다.

    이름*

    이메일

    전화

    왓츠앱*

    메시지

    제품
    콘택트 렌즈
    왓츠앱
    이메일