src="https://www.facebook.com/tr?id=26825290190466607&ev=PageView&noscript=1" />

ไม่มีศักดิ์ศรี ก่อนที่คนขี้โกงจะเกลียดชัง euismod fermentum sem semper the is erat, feugiat สิงห์ urna eget eros ดุส เอเนียน ตัดผมเพื่อเสียงหัวเราะ

Nail-Head Defects in HDI Drilling: A Practical Fault-Isolation Guide

  • Nail-Head Defects in HDI Drilling: A Practical Fault-Isolation Guide ผู้เขียน
  • 11th พฤศจิกายน 2026

The first clue may be a rejected cross-section, not a rough-looking hole. Copper at an inner layer has bent or spread, although the board surface looks ordinary. In HDI and multilayer production, that is a different investigation from chasing a visible burr. Keep the suspect panel, record its place in the drill stack, and examine a section before changing the setup. Otherwise an apparent improvement after a tool change may simply reflect a different panel or a different point in the drill’s life.

Nail-Head Defects in HDI Drilling A Practical Fault-Isolation Guide

In FR-4, the edge passes through glass fiber, resin, and copper. Glass is abrasive, resin retains heat, and copper can deform rather than break cleanly. TSHZ identifies worn edges and copper pulled during drill withdrawal as nail-head mechanisms in PCB work. A worn drill may also leave rough walls or drift from its intended hole position. The inspection sheet should have separate entries for those faults. “Bad holes” gives the next shift almost nothing to work with.

Confirm the defect before changing the drill

Where to inspect a cross-section

Nail heading is deformation of copper at the inner-layer interface visible in a prepared hole cross-section. Save an image of the whole hole as well as a close view of the affected layer. Label the layer, panel, and drilling sequence on the image. A nearby acceptable hole from the same setup is a useful reference. Without it, “rough” or “pulled” can mean different things to the drilling and quality teams.

A number written into a supplier FAQ is not the acceptance limit for every PCB. Use the drawing and the plant’s inspection method. If the copper shape is borderline, identify the measurement points and retain the prepared section. Preparation damage can confuse the reading; section another hole if necessary. Changing feed before the feature is agreed upon wastes a trial.

Separate nail heading, burrs, and resin smear

An entry or exit burr sits at the board surface. Nail heading sits at buried copper. Resin smear is different again: softened resin can coat the wall and interfere with exposed copper. The University of Maryland CALCE explanation of resin smear helps identify that wall condition. Several faults may be present on one panel. Give each one its own photograph and description.

Write a separate note for the surface burr and the buried copper. Add wall condition and hole position. Which panel was cut? A technician repeating the inspection tomorrow should be able to find the same feature without guessing. If a trial makes the entrance clean but leaves the inner layer distorted, the work is not finished.

Record the pattern across the panel and stack

Top versus lower panels

“Sample from the stack” is a poor label. Number the panels from top to bottom and put that number on each cross-section. An upper-panel failure that appears immediately may call for a fresh-tool or entry check; gradual deterioration down the stack points elsewhere. TSHZ’s PCB guidance warns that adding layers to a stack increases drill deflection risk and can reduce positional accuracy, especially with small diameters. A short drill is stiffer and less prone to wandering than an unnecessarily long one. Check both dimensions against the actual setup before deciding that nail heading is caused by wear alone.

The drilling traveler should identify entry and backing materials and how the panels were held. Measure actual drilling depth. Is the flute long enough to clear the full stack? Is the exposed drill longer than necessary? If coordinate data exist, compare hole position on upper and lower panels. A trend down the stack merits a setup check, even when edge wear is also visible.

Early holes versus late holes

Pick holes from the start and late part of the same drill run. Section them in the same way. A late sample with worse copper deformation is useful only if its laminate, hole size, and stack are known. Ask whether the wall has also become rougher or the hole position has moved. TSHZ recommends looking at hole-wall quality and visible edge wear when deciding when to replace a PCB micro drill. Keep the used edge with its sample record, rather than a tray of unlabelled drills.

The first holes are defective. That points to the setup before a wear-life discussion: was the specified drill fitted, did it seat correctly, what was the runout, and which entry and backing materials were used? Record feed, speed, and stack height. A defect that appears only much later has a different timeline; pull that drill and inspect its edge and flutes. Treating the two timelines as one problem makes both harder to solve.

Test the likely causes in order

Edge condition and replacement timing

Glass fiber in FR-4 abrades the edge; copper can be drawn into a deformed shape as the edge loses cutting ability or during withdrawal. In HDI drilling, carbide drill wear can coincide with nail heading, rough hole walls, and positional drift. That combination is a reason to examine the point and cutting edges, then match the edge photograph to the holes drilled with that tool. It is not a guarantee that another factory will see the symptoms in the same order.

Keep the first acceptable section and the last one before the defect limit is crossed. Put the corresponding edge images beside them. This gives purchasing and production a replacement point tied to their board, rather than a hole-count figure borrowed from another laminate. TSHZ also advises against routine regrinding of a diamond-coated micro drill because grinding can remove the coating and alter the edge geometry. If regrinding is attempted, its output belongs in a separate trial record.

Chip evacuation and heat

The hole contains a difficult mix: abrasive glass fiber, insulating resin, and ductile copper. Resin’s poor heat conduction can leave local heat around a drill, while packed chips change contact at the edge. Pull the suspect drill and inspect the flutes for loading. Section a nearby hole to check for smear. Heat and chip removal may matter even if nail heading is the rejected feature. The Arlon drilling-defects technical note gives a useful reference for reading drill wear alongside cutting conditions.

There is a temptation to change everything when scrap is rising. Resist it for the short diagnostic run. Change feed, or stack, or tool type, then compare the same panel position. Four simultaneous changes may produce a good section without showing which one helped. The withdrawal setting belongs on the sheet as well; the copper can be pulled on the way out.

Stack support, length, and machine condition

Measure runout at the fitted tool, not merely at an empty spindle. Check seating, spindle condition, and whether the stack lies flat. A short total length improves rigidity for PCB drilling; too many stacked panels increase deflection risk for small drills. That is a direction for testing, not a universal stack count. If one machine produces the damage and another does not, investigate the machine before assuming that the drill design is wrong.

On lower panels, look at the backing and the withdrawal move. On one suspect spindle, check the spindle. It sounds basic, yet a tool trial often arrives with no record of which copper layer was rejected. Attach two labelled sections to each change request: one before and one after. They will settle more than a note saying “new drill helped.”

When a different drill is the useful experiment

TS-A01UC for HDI micro-hole trials

TSHZ offers a ดอกสว่านเพชรสำหรับ PCB range for general multilayer and HDI boards. Its TS-A01UC micro drill is specified for HDI and multilayer work; the UC flute is intended to improve chip evacuation in dense small-hole drilling. It is worth trialling when worn edges or chip-packed flutes are part of the defect record. A fresh coated drill cannot compensate for a loose stack or a spindle running out.

Specify diameter and effective length against the finished-hole requirement, plating allowance, and actual stack. TSHZ also offers TS-A02 ST for standard FR-4/CEM work and TS-A03 for larger-diameter or thicker-board drilling. When comparing series, record the geometry and length as well as the coating; more than one property may have changed. The separate HDI and multilayer drill comparison covers that selection decision in more detail.

PCB diamond drill bit

Compare on the same board and inspection method

Run the candidate against the same laminate, stack, diameter, machine, and sectioning method as the current drill. Sample near the beginning and end of each tool run. Record the buried copper, surface burr, wall, hole position, and edge. An improved entrance with unchanged inner-layer distortion is an entrance improvement, not a nail-head solution. Extend the comparison far enough into the run to see whether the result holds.

What to send with a tooling inquiry

An inquiry is easier to answer when it includes the laminate and board build, copper-layer arrangement, finished-hole target, current drill diameter and length, total stack, machine, and spindle. Attach edge and cross-section images labelled with panel position and hole count. Include feed, speed, withdrawal settings, and the board’s own acceptance requirement. TSHZ’s หน้าแอปพลิเคชัน PCB covers the board-material context. The labelled samples show the precise failure under discussion.

คำถามที่พบบ่อย

Is every copper burr a nail head?

No. Surface burrs appear at entry or exit. Nail heading is evaluated at an inner copper layer in a prepared hole cross-section. Report both if both are present.

Does a diamond-coated drill remove the need to check the stack?

No. The drill edge, flute, length, stack support, runout, and withdrawal condition all affect the result. A coated tool trial is most informative after the defect pattern has been documented.

What should trigger a drill replacement review?

A change in hole-wall quality, nail-heading trend, roughness, positional accuracy, or visible cutting-edge wear is a reason to review the replacement interval. Use the plant’s own inspection requirement and board construction rather than a copied universal hole count.

แท็ก:

สารบัญ

คำถามที่พบบ่อย

"ราคาคือสิ่งที่คุณจ่าย ต้นทุนคือสิ่งที่คุณสูญเสีย เครื่องมือราคา 15 ดอลลาร์ที่ทำให้เครื่องจักรราคา 200,000 ดอลลาร์ของคุณหยุดทำงานทุกๆ 2 ชั่วโมง คือสิ่งที่มีราคาแพงที่สุดในโรงงานของคุณ เครื่องมือ CVD ของเรามีราคาสูงกว่า เพราะมันช่วยให้คุณใช้งานแกนหมุนได้ต่อเนื่อง 40 ชั่วโมงโดยไม่หยุดชะงัก อันไหนจะช่วยคุณประหยัดเงินได้มากกว่ากันในตอนสิ้นเดือน?"
ผมชอบคนขี้สงสัยครับ เพราะพวกเขามักจะกลายเป็นลูกค้าที่ดีที่สุดของเรา ในวัสดุ G5 กราไฟต์ หรืออะลูมิเนียมซิลิคอน 18% คาร์ไบด์มาตรฐานจะสึกหรอภายในไม่กี่นาที แต่ชั้นเคลือบเพชร HV$ ราคา 8000 ดอลลาร์ของเรานั้นทนทานต่อการสึกหรอได้อย่างเหลือเชื่อ เราไม่ได้แค่กล่าวอ้าง แต่เรามีรายงานการทดสอบการสึกหรอระดับจุลภาคมายืนยัน อยากดูวิดีโอเปรียบเทียบไหมครับ?
หยุดก่อน! ผมอยากขายเครื่องมือให้คุณนะ แต่เพชรกับเหล็กเป็น 'ศัตรู' กันที่อุณหภูมิสูง (ความสัมพันธ์ทางเคมี) สำหรับเหล็กกล้า ให้ใช้ซีรีส์ AlTiN ของเรา แต่ถ้าคุณกำลังตัดกราไฟต์ CFRP หรือเซรามิกส์ CVD ของเราคือสุดยอดเครื่องมืออย่างไม่ต้องสงสัย เราขายโซลูชัน ไม่ใช่แค่โลหะ
นั่นคือความแตกต่างระหว่าง DLC (Diamond-Like Carbon) กับ CVD แท้ๆ เครื่องมือ "เพชร" ราคาถูกส่วนใหญ่เป็นเพียงฟิล์มบางๆ เท่านั้น แต่ CVD ของเรานั้นถูกสร้างขึ้นทางเคมีลงบนพื้นผิวคาร์ไบด์ มันไม่ได้แค่เคลือบอยู่ด้านบน แต่มันเป็นส่วนหนึ่งของเครื่องมือ ไม่มีการลอกล่อน มีแต่การตัดที่บริสุทธิ์
ที่จริงแล้ว มันช่วยให้ดีขึ้นด้วยซ้ำ เพราะชั้นเพชรนั้นเรียบเนียนเป็นพิเศษ และคมมีดคงความคมได้นานกว่าถึง 20 เท่า คุณจึงหลีกเลี่ยงผลกระทบจากการ "ฉีกขาด" ของเครื่องมือที่ทื่อได้ คุณจะได้ผิวงานที่เงาวาวเหมือนกระจกแม้ในชิ้นที่ 100 ก็ตาม เหมือนกับชิ้นแรกๆ เลย
อย่าขายแค่เครื่องมือ แต่จงขาย 'กำลังการผลิตของเครื่องจักร' บอกลูกค้าของคุณว่า 'คุณอยากซื้อเครื่องมือ 1 ชิ้นแล้วใช้งานทั้งคืน หรือซื้อเครื่องมือ 20 ชิ้นแล้วจ้างคนมาคอยเปลี่ยนเครื่องมือให้?' แค่ค่าแรงที่ประหยัดได้ก็คุ้มทุนค่าเครื่องมือแล้ว
"เพชรชื่นชอบความเร็ว รอบหมุนสูงคือจุดที่มันเปล่งประกาย เราจัดเตรียมเอกสารข้อมูลการตัดแบบกำหนดเองให้พร้อมกับทุกคำสั่งซื้อ หากคุณไม่แน่ใจ โปรดส่งเกรดวัสดุของคุณมาให้เรา แล้วเราจะคำนวณค่า Vc และ Fz ที่เหมาะสมที่สุดให้คุณ เราไม่ได้แค่ส่งเครื่องมือ แต่เราส่งความสำเร็จ"
เราควบคุมความหนาของสารเคลือบให้อยู่ภายใน ±2 ไมครอน ในการผลิตอิเล็กโทรดกราไฟต์ที่มีความแม่นยำสูง เราทราบดีว่าไมครอนมีความสำคัญ รายงาน QC ของเราสำหรับทุกชุดการผลิตช่วยให้มั่นใจได้ว่าค่าความคลาดเคลื่อนจะคงที่ตั้งแต่เครื่องมือหมายเลข 1 ถึงเครื่องมือหมายเลข 100
เรามีสินค้าขนาดมาตรฐานพร้อมส่งทันที เราใช้บริการจัดส่งของ DHL/FedEx ซึ่งโดยทั่วไปจะใช้เวลา 4-7 วันถึงหน้าบ้านคุณ เรารู้ว่าเครื่องจักรเสียนั้นเหมือนแผลฉกรรจ์ และเราพร้อมที่จะช่วยหยุดเลือดไหลอย่างรวดเร็ว
เรามีตัวอย่างสินค้าพร้อม 'การรับประกันประสิทธิภาพ' สำหรับร้านค้าที่ผ่านเกณฑ์ เราไม่ได้แจกฟรีเพราะเทคโนโลยีระดับสูงมีราคา แต่ถ้าหากมันไม่สามารถทำงานได้ดีกว่าเครื่องมือที่คุณใช้อยู่ในปัจจุบันอย่างน้อย 10 เท่า ตัวต่อไปผมจะเป็นคนออกให้เอง ตกลงไหม?
ฟิล์มเพชรบริสุทธิ์ถูก "สร้าง" ขึ้นบนพื้นผิวของวัสดุคาร์ไบด์โดยใช้เทคโนโลยีการตกตะกอนไอสารเคมี (CVD) ฟิล์มนี้มีคุณสมบัติใกล้เคียงกับเพชรธรรมชาติ ทำให้เครื่องมือมีความแข็งและความทนทานต่อการสึกหรอเป็นพิเศษ
ความแข็งของสารเคลือบเพชร CVD สูงถึง 9000 HV ทำให้เป็นหนึ่งในสารเคลือบเครื่องมือที่แข็งที่สุดที่มีอยู่ในอุตสาหกรรมในปัจจุบัน
เมื่อทำการกลึงวัสดุกราไฟต์ อายุการใช้งานของเครื่องมือโดยทั่วไปจะเพิ่มขึ้น 3 ถึง 18 เท่า และในกระบวนการผลิตแผงวงจรพิมพ์ (PCB) อายุการใช้งานสามารถเพิ่มขึ้นได้ถึง 20 ถึง 30 เท่า
กราไฟต์มีฤทธิ์กัดกร่อนสูงและเปราะ ทำให้เครื่องมือทั่วไปสึกหรออย่างรวดเร็ว ความแข็งสูงของสารเคลือบเพชรช่วยต้านทานการสึกหรอและป้องกันการบิ่นที่คมตัดได้อย่างมีประสิทธิภาพ
ฟลุต 4 ฟลุต: เหมาะสำหรับการตกแต่งผิวงานหรือกราไฟต์แข็ง ให้ผิวงานที่เรียบเนียนกว่า 2 ฟลุต: เหมาะอย่างยิ่งสำหรับการเซาะร่องลึกหรือเครื่องมือขนาดเล็ก (ต่ำกว่า D2) ช่วยให้มีพื้นที่ระบายเศษวัสดุเพียงพอและป้องกันการแตกหักของเครื่องมือ
โดยหลักการแล้ว เส้นผ่านศูนย์กลางของดอกสว่าน = เส้นผ่านศูนย์กลางของรูที่เจาะเสร็จ ลบด้วยค่าชดเชยความหนาของทองแดงที่ชุบ โดยทั่วไปมักแนะนำให้เพิ่มค่าชดเชย 0.03–0.05 มม. สำหรับเส้นผ่านศูนย์กลางของรูที่เจาะเสร็จที่มีขนาดมากกว่า 0.5 มม.
ไม่ว่าจะเป็นการกลึงกราไฟต์หรือแผ่นวงจรพิมพ์ (PCB) ความยาวโดยรวมที่สั้นกว่าจะช่วยเพิ่มความแข็งแกร่ง ลดการเบี่ยงเบน และลดความเสี่ยงที่เครื่องมือจะแตกหักระหว่างการใช้งาน
หมายถึงการเสียรูปที่เกิดขึ้นบนผนังด้านในของรูที่เจาะเนื่องจากการสึกหรอของดอกสว่านหรือแรงดึงที่กระทำต่อแผ่นฟอยล์ทองแดงระหว่างการดึงกลับ การใช้เครื่องมือเคลือบเพชร CVD ช่วยลดหัวตะปูได้อย่างมาก ทำให้คุณภาพของผนังรูดีขึ้น
ไม่แนะนำให้ทำการเจียรแต่งรูปทรงใหม่ การเจียรแต่งรูปทรงจะทำให้สารเคลือบเพชรเสียหาย เผยให้เห็นพื้นผิวที่มีความแข็งน้อยกว่า และลดประสิทธิภาพลงอย่างมาก
โดยทั่วไป ควรเปลี่ยนเครื่องมือเมื่อคุณภาพของผนังรูเสื่อมลง (เช่น มีเสี้ยนหรือหัวตะปูเกิน 50 ไมโครเมตร) มีรอยสึกหรอที่ขอบที่มองเห็นได้ภายใต้กล้องจุลทรรศน์ หรือเมื่อปริมาณการใช้งานถึง 80–90% ของอายุการใช้งานที่แนะนำของเครื่องมือ
แม้ว่าราคาต่อหน่วยโดยทั่วไปจะสูงกว่าเครื่องมือทังสเตนคาร์ไบด์มาตรฐาน 3-5 เท่า แต่เนื่องจากมีอายุการใช้งานที่ยาวนานกว่า จึงทำให้ต้นทุนต่อรูเจาะต่ำกว่า และประหยัดกว่าในระยะยาว
ความแข็งและความทนทานสูง: เส้นใยแก้วในวัสดุ PCB มีความแข็งและเปราะมาก ทำให้ดอกสว่านทั่วไปสึกหรออย่างรวดเร็ว ครีบและหัวตะปู: แผ่นฟอยล์ทองแดงมีความยืดหยุ่นสูง ทำให้เกิดครีบได้ง่ายบริเวณปากรู หรือเกิดตำหนิคล้ายหัวตะปูเมื่อทะลุออก ส่งผลให้คุณภาพผนังรูไม่ดี ปัญหาการระบายความร้อน: เรซินมีค่าการนำความร้อนต่ำ ความร้อนสูงเฉพาะจุดอาจทำให้เครื่องมืออ่อนตัวลงได้
ทนทานต่อการสึกหรอสูงเป็นพิเศษ: ความแข็งของสารเคลือบผิวสูงถึง 9000HV ทำให้มีอายุการใช้งานยาวนานกว่าดอกสว่านคาร์ไบด์ทั่วไป 20-30 เท่า ลดข้อบกพร่อง: คมตัดที่คมกริบเป็นพิเศษช่วยลดการเกิดเสี้ยนและหัวตะปูได้อย่างมาก เสถียรภาพทางความร้อน: เพชรมีคุณสมบัติการนำความร้อนที่ดีเยี่ยม ช่วยให้ระบายความร้อนได้อย่างมีประสิทธิภาพและป้องกันการไหม้ของเรซินบนผนังรู
แผงวงจร HDI/หลายชั้น: แนะนำซีรี่ส์ TS-A01UC ซึ่งมีดีไซน์ร่อง UC พิเศษเพื่อการระบายเศษชิปที่เหนือกว่า เหมาะอย่างยิ่งสำหรับรูขนาดเล็กที่มีความหนาแน่นสูง เมนบอร์ด FR-4/CEM มาตรฐาน: แนะนำรุ่น TS-A02 ST มาตรฐาน เนื่องจากมีอัตราส่วนราคาต่อประสิทธิภาพที่ดีที่สุด แผ่นไม้ขนาดใหญ่/หนา: แนะนำให้ใช้ซีรีส์ TS-A03 ซึ่งสามารถเจาะรูได้ลึกถึง 6.50 มม. โดยมีก้านดอกสว่านขนาดใหญ่กว่าเส้นผ่านศูนย์กลางของดอกสว่าน
ครีบทางออก: เพิ่มแผ่นรองหลังอะลูมิเนียมหนา 0.3–0.5 มม. ไว้ใต้แผงวงจร และปรับพารามิเตอร์การดึงกลับให้เหมาะสม รอยบิ่นขณะเจาะ: ลดอัตราการป้อนขณะเจาะ หรือเปลี่ยนไปใช้ดอกสว่านเคลือบเพชรที่คมกว่า
ผลิตภัณฑ์ล่าสุด

ดูสินค้าของเราได้ที่นี่

ดูเพิ่มเติม
PCB drilling bit

ดอกสว่านเพชรสำหรับ PCB

ดอกสว่าน PCB ที่มีคุณสมบัติในการกำจัดเศษวัสดุและปรับความเรียบของรูได้ดีเยี่ยม อายุการใช้งานยาวนาน เหมาะสำหรับการเจาะแผ่นวงจรพิมพ์หลายชั้นและ HDI ทั่วไป แผ่น FR-4, CEM-1 และแผ่นวงจรพิมพ์ที่เป็นมิตรต่อสิ่งแวดล้อม ช่วงเส้นผ่านศูนย์กลาง: 0.1–3.175 มม. สำหรับแผงวงจรพิมพ์ (PCB) รุ่นใหม่ล่าสุด ดอกสว่านเคลือบเพชรสามารถเจาะรูได้มากกว่า 3,000 รูต่อดอก
อ่านเพิ่มเติม
Diamond-coated PCB tool

ดอกกัดเคลือบเพชรสำหรับแผ่นวงจรพิมพ์ (PCB)

ดอกกัดเคลือบเพชรสำหรับ PCB หรือที่รู้จักกันในชื่อดอกกัดร่อง PCB ดอกกัดแผงวงจรพิมพ์ หรือดอกกัดแกะสลัก ส่วนใหญ่ใช้สำหรับการตัดตามรูปทรง การเซาะร่อง การกัดควบคุมความลึก การเซาะร่องตัววี การเจาะรูครึ่งรู และการลบคมนิ้วทองคำบน PCB โดยเป็นเครื่องมือคาร์ไบด์ที่ใช้กันมากที่สุดในกระบวนการผลิตหลังการผลิต PCB
อ่านเพิ่มเติม
Dental-burs-1

หัวเจาะฟันเพชร CVD

การตัดที่แม่นยำระดับไมครอน ผสานความทนทานต่อการสึกหรอสูงสุดเข้ากับประสบการณ์การใช้งานทางคลินิกที่อ่อนโยน ชุดหัวเจาะฟันนี้ผลิตจากสแตนเลส/คาร์ไบด์บริสุทธิ์สูง เคลือบด้วยนาโนไดมอนด์ CVD ขั้นสูง (หรือการชุบด้วยไฟฟ้าของเม็ดเพชรธรรมชาติความหนาแน่นสูง) ออกแบบมาสำหรับขั้นตอนทางคลินิกที่มีความเข้มข้นสูง เช่น การเตรียมฟัน การเปิดโพรงฟัน การกำจัดฟันผุ การบูรณะฟันเพื่อความสวยงาม (การเตรียมวีเนียร์) และการตัดครอบฟัน/สะพานฟัน การเคลือบเพชรที่แข็งเป็นพิเศษและกระจายตัวอย่างสม่ำเสมอให้ประสิทธิภาพการตัดที่สูง ในขณะเดียวกันก็ลดความร้อนจากการเสียดสีเพื่อปกป้องเนื้อเยื่อในโพรงฟัน ทำให้เป็นตัวเลือกที่ดีที่สุดสำหรับทันตกรรมดิจิทัลสมัยใหม่
อ่านเพิ่มเติม
Flat-bottom-cylindrical-end-mill-1

ดอกกัดปลายทรงกระบอกก้นแบนเคลือบเพชร

ดีไซน์มาตรฐาน 2 ฟลุต/4 ฟลุต พร้อมคมตัดที่คมกริบและพื้นที่ระบายเศษขนาดใหญ่ เหมาะสำหรับการกัดหยาบและกัดกึ่งละเอียดของอิเล็กโทรดกราไฟต์อย่างมีประสิทธิภาพ
อ่านเพิ่มเติม
Get Standed
เครื่องมือของคุณทันสมัยทันยุค "การผลิตชิ้นส่วนที่ยากต่อการผลิตด้วยเครื่องจักร" หรือไม่?

ฝากข้อความไว้

กราไฟต์ เซรามิก และคาร์บอนไฟเบอร์ คืออนาคต แต่พวกมันก็เป็น “ตัวทำลายเครื่องมือ” เช่นกัน หากคุณยังคงใช้สารเคลือบแบบดั้งเดิม คุณกำลังต่อสู้กับสิ่งที่ไม่มีวันชนะ
การเคลือบเพชรด้วยวิธี CVD (Chemical Vapor Deposition) ของเรา สร้างชั้นเพชรผลึกแท้บนพื้นผิวคาร์ไบด์ นี่ไม่ใช่แค่ "การเคลือบผิว" แต่เป็นเกราะป้องกัน

เหตุผลที่ผู้จัดจำหน่ายชั้นนำเลือกใช้ผลิตภัณฑ์ซีรี่ส์ CVD ของเรา:
1. แรงเสียดทานต่ำมาก: ป้องกันการเชื่อมติดกันของเศษโลหะและการสะสมความร้อน
2. ทนทานต่อการเสียดสีสูงเป็นพิเศษ: รักษาความคมของใบมีดได้นานกว่าถึง 20 เท่า
3. ผิวสำเร็จ: ผิวชิ้นงานเรียบลื่นเหมือนกระจก ไม่จำเป็นต้องขัดเงาซ้ำอีก

    ชื่อของคุณ*

    อีเมล

    โทร.

    WhatsApp*

    ข้อความ

    สินค้า
    การติดต่อ
    วาส
    อีเมล