没有尊严,在 celerisque 面前是 euismod 发酵仇恨 sem semper the iserat,一个 feugiat leo urna eget eros。杜伊斯埃涅安 为了博君一笑而剪的头发。

Nail-Head Defects in HDI Drilling: A Practical Fault-Isolation Guide

  • Nail-Head Defects in HDI Drilling: A Practical Fault-Isolation Guide 作者
  • 11th 11 月 2026

The first clue may be a rejected cross-section, not a rough-looking hole. Copper at an inner layer has bent or spread, although the board surface looks ordinary. In HDI and multilayer production, that is a different investigation from chasing a visible burr. Keep the suspect panel, record its place in the drill stack, and examine a section before changing the setup. Otherwise an apparent improvement after a tool change may simply reflect a different panel or a different point in the drill’s life.

Nail-Head Defects in HDI Drilling A Practical Fault-Isolation Guide

In FR-4, the edge passes through glass fiber, resin, and copper. Glass is abrasive, resin retains heat, and copper can deform rather than break cleanly. TSHZ identifies worn edges and copper pulled during drill withdrawal as nail-head mechanisms in PCB work. A worn drill may also leave rough walls or drift from its intended hole position. The inspection sheet should have separate entries for those faults. “Bad holes” gives the next shift almost nothing to work with.

Confirm the defect before changing the drill

Where to inspect a cross-section

Nail heading is deformation of copper at the inner-layer interface visible in a prepared hole cross-section. Save an image of the whole hole as well as a close view of the affected layer. Label the layer, panel, and drilling sequence on the image. A nearby acceptable hole from the same setup is a useful reference. Without it, “rough” or “pulled” can mean different things to the drilling and quality teams.

A number written into a supplier FAQ is not the acceptance limit for every PCB. Use the drawing and the plant’s inspection method. If the copper shape is borderline, identify the measurement points and retain the prepared section. Preparation damage can confuse the reading; section another hole if necessary. Changing feed before the feature is agreed upon wastes a trial.

Separate nail heading, burrs, and resin smear

An entry or exit burr sits at the board surface. Nail heading sits at buried copper. Resin smear is different again: softened resin can coat the wall and interfere with exposed copper. The University of Maryland CALCE explanation of resin smear helps identify that wall condition. Several faults may be present on one panel. Give each one its own photograph and description.

Write a separate note for the surface burr and the buried copper. Add wall condition and hole position. Which panel was cut? A technician repeating the inspection tomorrow should be able to find the same feature without guessing. If a trial makes the entrance clean but leaves the inner layer distorted, the work is not finished.

Record the pattern across the panel and stack

Top versus lower panels

“Sample from the stack” is a poor label. Number the panels from top to bottom and put that number on each cross-section. An upper-panel failure that appears immediately may call for a fresh-tool or entry check; gradual deterioration down the stack points elsewhere. TSHZ’s PCB guidance warns that adding layers to a stack increases drill deflection risk and can reduce positional accuracy, especially with small diameters. A short drill is stiffer and less prone to wandering than an unnecessarily long one. Check both dimensions against the actual setup before deciding that nail heading is caused by wear alone.

The drilling traveler should identify entry and backing materials and how the panels were held. Measure actual drilling depth. Is the flute long enough to clear the full stack? Is the exposed drill longer than necessary? If coordinate data exist, compare hole position on upper and lower panels. A trend down the stack merits a setup check, even when edge wear is also visible.

Early holes versus late holes

Pick holes from the start and late part of the same drill run. Section them in the same way. A late sample with worse copper deformation is useful only if its laminate, hole size, and stack are known. Ask whether the wall has also become rougher or the hole position has moved. TSHZ recommends looking at hole-wall quality and visible edge wear when deciding when to replace a PCB micro drill. Keep the used edge with its sample record, rather than a tray of unlabelled drills.

The first holes are defective. That points to the setup before a wear-life discussion: was the specified drill fitted, did it seat correctly, what was the runout, and which entry and backing materials were used? Record feed, speed, and stack height. A defect that appears only much later has a different timeline; pull that drill and inspect its edge and flutes. Treating the two timelines as one problem makes both harder to solve.

Test the likely causes in order

Edge condition and replacement timing

Glass fiber in FR-4 abrades the edge; copper can be drawn into a deformed shape as the edge loses cutting ability or during withdrawal. In HDI drilling, carbide drill wear can coincide with nail heading, rough hole walls, and positional drift. That combination is a reason to examine the point and cutting edges, then match the edge photograph to the holes drilled with that tool. It is not a guarantee that another factory will see the symptoms in the same order.

Keep the first acceptable section and the last one before the defect limit is crossed. Put the corresponding edge images beside them. This gives purchasing and production a replacement point tied to their board, rather than a hole-count figure borrowed from another laminate. TSHZ also advises against routine regrinding of a diamond-coated micro drill because grinding can remove the coating and alter the edge geometry. If regrinding is attempted, its output belongs in a separate trial record.

Chip evacuation and heat

The hole contains a difficult mix: abrasive glass fiber, insulating resin, and ductile copper. Resin’s poor heat conduction can leave local heat around a drill, while packed chips change contact at the edge. Pull the suspect drill and inspect the flutes for loading. Section a nearby hole to check for smear. Heat and chip removal may matter even if nail heading is the rejected feature. The Arlon drilling-defects technical note gives a useful reference for reading drill wear alongside cutting conditions.

There is a temptation to change everything when scrap is rising. Resist it for the short diagnostic run. Change feed, or stack, or tool type, then compare the same panel position. Four simultaneous changes may produce a good section without showing which one helped. The withdrawal setting belongs on the sheet as well; the copper can be pulled on the way out.

Stack support, length, and machine condition

Measure runout at the fitted tool, not merely at an empty spindle. Check seating, spindle condition, and whether the stack lies flat. A short total length improves rigidity for PCB drilling; too many stacked panels increase deflection risk for small drills. That is a direction for testing, not a universal stack count. If one machine produces the damage and another does not, investigate the machine before assuming that the drill design is wrong.

On lower panels, look at the backing and the withdrawal move. On one suspect spindle, check the spindle. It sounds basic, yet a tool trial often arrives with no record of which copper layer was rejected. Attach two labelled sections to each change request: one before and one after. They will settle more than a note saying “new drill helped.”

When a different drill is the useful experiment

TS-A01UC for HDI micro-hole trials

TSHZ offers a PCB金刚石钻头 range for general multilayer and HDI boards. Its TS-A01UC micro drill is specified for HDI and multilayer work; the UC flute is intended to improve chip evacuation in dense small-hole drilling. It is worth trialling when worn edges or chip-packed flutes are part of the defect record. A fresh coated drill cannot compensate for a loose stack or a spindle running out.

Specify diameter and effective length against the finished-hole requirement, plating allowance, and actual stack. TSHZ also offers TS-A02 ST for standard FR-4/CEM work and TS-A03 for larger-diameter or thicker-board drilling. When comparing series, record the geometry and length as well as the coating; more than one property may have changed. The separate HDI and multilayer drill comparison covers that selection decision in more detail.

PCB diamond drill bit

Compare on the same board and inspection method

Run the candidate against the same laminate, stack, diameter, machine, and sectioning method as the current drill. Sample near the beginning and end of each tool run. Record the buried copper, surface burr, wall, hole position, and edge. An improved entrance with unchanged inner-layer distortion is an entrance improvement, not a nail-head solution. Extend the comparison far enough into the run to see whether the result holds.

What to send with a tooling inquiry

An inquiry is easier to answer when it includes the laminate and board build, copper-layer arrangement, finished-hole target, current drill diameter and length, total stack, machine, and spindle. Attach edge and cross-section images labelled with panel position and hole count. Include feed, speed, withdrawal settings, and the board’s own acceptance requirement. TSHZ’s PCB应用页面 covers the board-material context. The labelled samples show the precise failure under discussion.

常问问题

Is every copper burr a nail head?

No. Surface burrs appear at entry or exit. Nail heading is evaluated at an inner copper layer in a prepared hole cross-section. Report both if both are present.

Does a diamond-coated drill remove the need to check the stack?

No. The drill edge, flute, length, stack support, runout, and withdrawal condition all affect the result. A coated tool trial is most informative after the defect pattern has been documented.

What should trigger a drill replacement review?

A change in hole-wall quality, nail-heading trend, roughness, positional accuracy, or visible cutting-edge wear is a reason to review the replacement interval. Use the plant’s own inspection requirement and board construction rather than a copied universal hole count.

标签:

目录

常见问题解答

价格是你付出的,成本是你损失的。一个价值 15 美元的工具,如果每 2 小时就让你的价值 20 万美元的机器停机,那它就是你车间里最贵的东西。我们的 CVD 工具价格更高,因为它能为你争取 40 小时的不间断主轴运转时间。到月底,哪一个能为你节省更多?
我喜欢持怀疑态度的人——他们通常会成为我们最好的客户。在G5石墨或18%硅铝合金中,普通碳化物会在几分钟内发生磨损。而我们价值8000美元的HV级金刚石晶体层则完全不受这种磨损的影响。我们并非只是声称如此;我们有微磨损测试报告来佐证。想看看对比视频吗?
先别急。我很想向您推销工具,但金刚石和铁在高温下是“敌人”(化学亲和力)。切割钢材请使用我们的AlTiN系列产品。但如果您要切割石墨、碳纤维增强复合材料或陶瓷,我们的CVD工艺绝对是最佳选择。我们提供的是解决方案,而不仅仅是金属。
这就是类金刚石碳 (DLC) 和真正 CVD 的区别。大多数廉价的“金刚石”刀具只是薄膜。我们的 CVD 技术是将碳化物通过化学方法生长到碳化物基体中。它并非仅仅覆盖在表面,而是刀具的一部分。不会剥落,只有纯粹的切削。
实际上,它还能提升加工效果。因为金刚石涂层极其光滑,刀刃锋利度保持时间延长20倍,所以可以避免钝刀造成的“撕裂”现象。即使是第一百个零件,也能像第一个零件一样,获得镜面般的光滑效果。
不要向他们推销工具;要向他们推销“机器产能”。告诉你的客户:“您是愿意买 1 个工具通宵工作,还是买 20 个工具,然后雇人站在那里更换它们?” 单单节省的人工成本就足以抵消工具的成本。
“钻石喜欢高速切割。高转速是它大放异彩的地方。我们为每份订单提供定制的切割数据表。如果您不确定,请告诉我们您的材料牌号,我们将为您计算最佳的Vc和Fz值。我们交付的不仅仅是工具,更是成功。”
我们可将涂层厚度控制在±2微米以内。在高精度石墨电极加工中,我们深知微米级的精度至关重要。我们对每一批产品都进行质量控制,确保从第一把刀具到第一百把刀具,偏移量始终保持一致。
我们备有标准尺寸的现货,可立即发货。我们使用DHL/FedEx快递,通常4-7天即可送达您家门口。我们深知机器故障如同流血的伤口,而我们会迅速止住这道血。
我们为符合条件的店铺提供“性能保证”样品。高端技术是有成本的,所以我们不会免费赠送,但如果它的性能没有比您现有的工具至少提升10倍,那么下一台样品就免费。这样说可以吗?
利用化学气相沉积(CVD)技术,在碳化物基体表面“生长”一层纯金刚石薄膜。该薄膜的性能接近天然金刚石,赋予刀具卓越的硬度和耐磨性。
CVD金刚石涂层的硬度可达9000HV,是目前工业界最硬的工具涂层之一。
加工石墨材料时,刀具寿命通常会增加 3 到 18 倍;在 PCB 加工中,寿命延长可达 20 到 30 倍。
石墨具有极强的磨蚀性和脆性,会导致传统刀具快速磨损。金刚石涂层的高硬度能够有效抵抗磨损,并防止切削刃崩刃。
4 刃:适用于精加工或硬质石墨,可提供更好的表面光洁度。 2 刃:非常适合深槽加工或小直径刀具(小于 D2),确保足够的排屑空间,防止刀具断裂。
原则上,钻孔直径 = 成品孔径 - 镀铜层厚度补偿。通常建议,对于成品孔径超过 0.5 毫米的情况,增加 0.03–0.05 毫米的补偿。
无论是加工石墨还是PCB,较短的总长度都能提高刚性,减少跳动,并最大限度地降低操作过程中刀具断裂的风险。
这指的是由于钻头磨损或拔出过程中铜箔受到拉力而导致的钻孔内壁变形。使用 CVD 金刚石涂层刀具可显著减少钉头变形,从而提高孔壁质量。
不建议重新研磨。重新塑形会损坏金刚石涂层,暴露硬度较低的基材,从而大幅降低性能。
通常情况下,当孔壁质量恶化(例如,毛刺或钉头超过 50 μm)、在显微镜下可见边缘磨损,或者加工量达到推荐刀具寿命的 80-90% 时,应更换刀具。
虽然它们的单价通常是标准碳化钨刀具的 3-5 倍,但由于其使用寿命更长,因此每个孔的成本更低,从长远来看更经济。
高磨蚀性:PCB材料中的玻璃纤维非常坚硬且易碎,导致标准钻头快速磨损。 毛刺和钉头:铜箔具有很高的延展性,因此在孔入口处容易形成毛刺,在出口处容易形成“钉头”缺陷,导致孔壁质量差。 散热问题:树脂导热性差;局部过热会导致工具软化。
超高耐磨性:涂层硬度达到 9000HV,使用寿命比传统硬质合金钻头长 20-30 倍。 减少缺陷:极其锋利的切削刃可显著减少毛刺和钉头的形成。 热稳定性:金刚石具有优异的导热性,能够有效散热并防止树脂在孔壁上烧焦。
HDI/多层板:推荐 TS-A01UC 系列,采用特殊的 UC 槽设计,具有优异的排屑性能,是高密度微孔的理想选择。 标准 FR-4/CEM 板:推荐 TS-A02 ST 标准系列,提供最佳性价比。 大直径/厚板:推荐使用 TS-A03 系列,其柄径大于钻头直径,可钻直径达 6.50 毫米的孔。
出口毛刺:在电路板下方添加 0.3–0.5 毫米铝制背板,并优化回缩参数。 入口毛刺:降低入口进给速度或换用更锋利的金刚石涂层钻头。
最新产品

了解我们的产品

查看更多
PCB drilling bit

PCB金刚石钻头

PCB钻头具有优异的排屑和孔粗糙度控制能力,使用寿命长,适用于钻削普通多层板和HDI板、FR-4板、CEM-1板以及环保板。 直径范围:0.1–3.175 毫米,对于最新的 PCB 板,金刚石涂层钻头每个钻头可钻 3000 多个孔。
阅读更多
Diamond-coated PCB tool

PCB金刚石涂层铣刀

PCB金刚石涂层铣刀,又称PCB开槽铣刀、印刷电路板铣刀或雕刻刀,主要用于PCB的轮廓切割、开槽、深度控制铣削、V形槽加工、半孔加工和金手指倒角;它们是PCB后制造工艺中最常用的硬质合金刀具。
阅读更多
Dental-burs-1

CVD金刚石牙科钻头

微米级精密切割,兼具极致耐磨性和温和的临床体验。该系列牙科钻头采用高纯度一体式不锈钢/硬质合金基材,并涂覆先进的CVD纳米金刚石(或高密度天然金刚石颗粒电镀)。专为高强度临床操作而设计,例如牙体预备、开洞、龋齿去除、美容修复(贴面预备)以及牙冠/牙桥切割。超硬且均匀分布的金刚石涂层可提供强大的切割效率,同时最大限度地减少摩擦生热,从而保护牙髓,使其成为现代数字化牙科的理想之选。
阅读更多
Flat-bottom-cylindrical-end-mill-1

金刚石涂层平底圆柱立铣刀

标准 2 刃/4 刃设计,具有锋利的切削刃和较大的排屑空间,适用于石墨电极的高效粗加工和半精加工。
阅读更多
Get Standed
您的刀具是否跟得上“难加工材料”时代的发展?

留言

石墨、陶瓷和碳纤维代表着未来,但它们也是“工具杀手”。如果你还在使用传统涂层,那你就注定要失败。
我们的 CVD(化学气相沉积)金刚石涂层可在碳化物基材上形成真正的晶体金刚石层。这不仅仅是一种“表面处理”,而是一种保护层。

为什么顶级分销商选择我们的 CVD 系列产品:
1.超低摩擦:防止切屑焊接和热量积聚。
2.极强的耐磨性:保持锋利刀刃的时间延长20倍。
3.表面光洁度:工件表面达到镜面效果,无需二次抛光。

    您的姓名*

    电子邮件

    电话

    WhatsApp*

    信息

    产品
    联系方式
    WhatsApp
    电子邮件